Product Description
Product Name: Flame Retardant Gel coat HS - LFI7035S
1. Brief Introduction:
HS-LFI7035S Gelcoat is an intumescent flame retardant gel coat, which the base resin is Isophthalic-adipic acid unsaturated polyester resin, it is suitable for spray process and it is pre-promoted. The gel coat is suitable for the surface of FRP products requiring flame retardant. It is applicated in rail transit, wind turbine nacelle cover, ship accessories and other fields with requirements for flame retardant.
2. Features:
· Good construction performance;
· Excellent flame retardant performance(high oxygen index, low smoke density);
· Meet fire protection standards UIC564-2 Class B
· Good water and weather resistance.
3.Gelcoat Properties:
Test Item |
Unit |
Test Value |
Test Method |
Appearance |
-- |
Gray paste liquid |
-- |
Viscosity(25ºC) |
mP·s |
5000-8500 |
ISO2555:2018 Brookfield
RV/DV-I Spindle 6-10 RPM |
Gel time(25ºC) |
min |
15.0-35.0 |
ISO2535:2003 |
Thixotropic index |
-- |
≥3 |
ISO2555:2018Brookfield |
RV/DV-I |
Gel time test:Curing agent M-50(AKZO) 2%.
4. Application Notes:
1). Mix the gelcoat in bucket gently before use, avoid excessive high shear rates and avoid air entrapment during mixing.
2). Ideal application temperature should be between 18-25°C and humidity less then 80%. Mold should be polished and clean before gelcoat application.
3). Prepare the mold so that the surface is dry, clean and oil-free.
4). The surface of the mould should be fully waxed (do not use the release wax containing silicone), and the water-soluble release wax must wait for its moisture to evaporate before spraying the gelcoat.
5). The curing agent used for gelcoat is MEKP (the dosage is generally 1-3%).
6). The total thickness of gelcoat film should be between 600 and 1000μm. The thickness of each spray shall not be more than 0.2mm, wait for 2-3 minutes after the solvent volatilizes, then spray to the required thickness..
7). Check gelcoat cure degree before starting lamination layers. Press your finger for 30 seconds on gelcoat film to check cure degree. When you do not see gelcoat residue on your finger but gelcoat to remain sticky on the film, you can continue with lamination layers.
5. Operation procedure:
Note: Spray with paint spray can, the air source pressure is maintained at 20psi, the air flow per minute is not less than 0.6 cubic meters.
1). Prepare for spraying according to the requirements of the application guide.
2). Apply a thin layer of easy polishing primer (thickness no more than 0.2mm) on the surface of the original mold using the method of thin layer and multiple passes, and then wait to dissolve. After 2 minutes of evaporation, spray the next layer to the desired thickness. The primer will dry within 1 hour and you can start sanding.
3). Dry sanding with 220-320 mesh sandpaper, then sand with 600-1200 mesh water sandpaper, and then polish.
6. Storage:
1) Avoid exposure to heat sources such as direct sunlight or steam pipes. Stored in a dry place at temperatures below 25ºC.
2) Keep sealed to prevent moisture pick-up and monomer loss. Prolonged storage outside of recommended conditions can influence liquid resin properties like viscosity and gel time.
3) Transportation should fit the State Council "Chemistry Dangerous Articles Safety Management Regulations". Because it contains styrene monomer, it is hazardous and inflammable.
Packaging & Shipping
Application
Certifications
FAQ
Q: Is Your Company a Manufacturer?
A: Yes, indeed.We have 48,800 square meters factory located in Jiangsu Province, China.
Q: Can I Request a Sample of Unsaturated Polyester Resin?
A: Yes,we can provide 1kg of resin as a free sample, but freight are typically the responsibility of the buyer.
Q: Do you have OEM/ODM service?
A: Yes, we are highly flexible in offering OEM/ODM services.
Q: Can I Customize the Formulation of Unsaturated Polyester Resin for My Project?
A: Yes, absolutely. We understand that different projects may have unique requirements. Our R & D department is well-equipped to handle custom formulations based on your specific needs. You can provide us with the details of your project, including any specific characteristics or performance criteria you are looking for, and our experts will work on tailoring a formulation that meets your requirements.
Q: How Do I Choose the Right Unsaturated Polyester Resin for My Application?
A: We would provide guidance on selecting the appropriate UPR based on different project requirements.
Q: What Certifications and Quality Standards Does Your Unsaturated Polyester Resin Meet?
A: Our Unsaturated Polyester Resin meets CCS, RoHS, REACH, EMS, and QMS certifications and quality standards.
Q: What is Your Company's International Transportation Form?
A: For samples, we offer Delivery Duty Paid (DDP) services for most of the countries. This means that we handle the delivery process, including the payment of taxes, and you won't be required to manage customs clearance. For bulk orders, we normally transported by sea or land. Our commitment is to ensure the secure and efficient delivery of our products to your specified destination.
Q: What is The Product Lead Time?
A: 15 days.
Q:Can I Get a Lower Price for a Large Quantity Order ?
A: Absolutely. The online price serves as a reference, but due to fluctuations in raw material costs, our sales team can provide you with the most accurate and competitive pricing. Before making a purchase, kindly engage with our sales representatives. They will work closely with you, taking into account your order quantity and specific requirements, to ensure you receive the best and most cost-effective pricing tailored to your needs.
Q:What's Shelf Life of Unsaturated Polyester Resin ?
A: Normally 6 months.